AVR5 om (e) 2/5/99 10:38 AM Page 13
Remote Control Functions
13
IMPORTANT NOTE: The AVR5Os AVR Selector:Press this button to
Surround/Channel Selectors:
remote may be programmed to con-use the remote control for operation of
Press these buttons to check or
trol up to three additional devices,the AVR5. Note that the button will
change the current Surround mode.
including the AVR5. Before using thebriefly turn red after it has beenWhen either one of these two buttons
remote, it is important to remember topressed to confirm your selection.is first pressed, the Information
press the Device Control Selector
Displayo will show the current
button ? that corresponds to the� Source SelectorPrs:ess theseSurround mode. Press either button
unit you wish to operate. The remotebuttons to select an input source for
again to change the current
is capable of operating a wide varietythe AVR5. The AM/FM button is alsoSurround mode by scrolling the list
of products using the control codesused to switch between frequencyof available modes as they appear
that are part of the remote. Beforebands when the tuner is in use.in the Information Displao.y
using the remote with other products,
When the remote is being used to
follow the instructions on pagesNOTE: Pressing one of these buttons
control a VCR or TV set, these but-
23�26 to program the proper codesselects the source only. In order totons are used to change channels.
for the products in your system.control the actual source machineThese buttons are also used when
using the remote you must press thethe remote is being programmed to
It is also important to remember thatDevice Control Selectorbutton ÂOfindÃ� the correct codes via the
many of the buttons on the remotefor the desired product.
Search mode. (See page 23 for
take on different functions, depend-more information on programming
ing on the product selected using? 6-Channel Direct:Press this but-the remote.)
the Device Control Selectors. Theton to use the output of an optional,
descriptions shown here primarilyexternal digital decoder as the� Clear Button:This button is used
detail the functions of the remoteAVR5Os input source.to clear preset memory information
when it is used to operate the AVR5.for the AVR5Os tuner. (See pages
(See page 24 for information aboutú Disc Skip:These buttons do not21�22 for more information on tuner
alternate functions for the remoteOshave any functions when controllingpresets.)
buttons.)the AVR5, but they operate the Disc
Skip functions of compatible Harman? Master Volume:Press these
� LED Indicator:This indicator Kardon compact disc changers. The
buttons to raise or lower the AVR5Os
will flash whenever a button isDisc Skip Up button will also function
volume. These buttons are also used
pressed to confirm that a remoteas the Open/Close button for certain
to obtain the IR code numbers for a
command is being transmitted. It willDVD and LD equipment when the
device that has been programmed
also flash while the remote is beingremote is properly programmed to
into the remote. (See page 23 for
programmed to assist in entering orcontrol them.more information on programming
reading remote codes. Note that this
the remote.)
is NOT a standard remote button,Sleep Button:Press this button
and has no function when pressed.to place the unit in the Sleep mode.Mute:Press this button to momen-
After the time shown in the display,tarily silence the AVR5. When the
o Main Power Off:When the AVR5the AVR5 will automatically go into
AVR5 remote is being programmed to
is turned on, press this button tothe Standby mode. Each press ofoperate another device, this button is
place it in the Standby mode. Notethe button changes the time untilpressed with the Device Control
that in this condition, the unit is stillturn-off in the following order:Selectorbutton ? to begin the pro-
connect to AC Power.
9080706050gramming process. (See page 23 for
minminminminmin
more information on programming
Ť Main Power On:When the AVR540302010OFFthe remote.)
is in the Standby mode, as indicatedminminminmin
by the Power Indicator3 glowing
ż PYScan:Press this button to
green, press this button to turn the
A Dimmer:Press this button onceautomatically scan through the list of
AVR5 on.
to reduce the brightness of the frontstations that are programmed into
the AVR5Os tuner memory. When the
panel display to half the normal
? Device Control SelectorPresss:button is pressed, each preset sta-
intensity. Press it again to turn the
one of these buttons to use thetion will play for five seconds before
front panel display completely off.
remote to control the functions ofthe next station is selected. Press
When the display is completely off,
another audio/video device. Note
press the button to return to normalthe button again when the desired
that the button will briefly turn redstation is heard to stop the preset
brightness.
after it has been pressed to confirmscan.
your selection. (See pages 23�25 for
information on programming the
AVR5Os remote to operate these
devices.) |
ACEC
